Freestanding STANCHION 39"

This is the taller version of the Absolute stanchion system designed for use where the demarcation needs to be more obvious. As with the 16" stanchion, it discreetly indicates that visitors should not touch the exhibits and it’s neutral finish and clean lines sit comfortably within the museum and gallery environment, gently reminding the public of it’s presence without clashing with the display or decor. The clever bit is a stretchy cord, that fits snugly into the top of each post, drawing a neat line in the air, avoiding the distraction of that dreadful droopy rope. Because the elasticated cord makes a straight line, it blends with the architecture of the building helping the stanchions to become less obvious and ensuring the artwork is the object of attention.

The large stable steel base and tall upright supports the elasticated cord and this defines restricted access, but gives to the touch. The base is cushioned with slip resistant neoprene pads to improve grip and protect polished floor surfaces. The stanchion works very well as part of a permanent installation and has the flexibility to be easily re-arranged for temporary exhibits.

Dimensions & Finish

The stanchions are 39" high with a 13" diameter base and available in two hardwearing versions:

Freestanding Barrier PPC Grey 39in(1000mm) - PPC Cover Plate

Please contact Eloise Wierzbicki for the best price.

Freestanding Barrier SS 39in (1000mm) - SS Cover Plate

Please contact Eloise Wierzbicki for the best price.

Freestanding Barrier PPC Black 16in (1000mm)

Please contact Eloise Wierzbicki for the best price.

Freestanding Barrier PPC White 16in (1000mm)

Please contact Eloise Wierzbicki for the best price.

Other sizes and finishes are available on request.

ACCESSORIES FOR THE 39" FREESTANDING Stanchion

You will of course require elasticated cord to go with your stanchion layout.

Wall terminators are an excellent way to complete some stanchion installations by returning the line of cord back to the wall.

You can now apply information signage directly to the top of our stanchions by using one of our signage adaptors that will accept our range of aluminum labelholders.

If you require additional top caps then you can order them from here.

Our stanchions are supplied complete with an Allen key and that is the only tool you will require to assemble them but if you need more keys, just ask.

USEFUL TIPS AND GUIDELINES

It is important to select a stanchion finish that blends well with the environment and minimises visual impact, and to assist this process our standard cord colour is grey. However in areas where it is important to draw attention to the line we can supply cord in a range of colours that will enhance the contrast. These are white, red or black.

If a floor is highly polished the stanchions will need to be closer together (5') than a floor that has plenty of grip, in which case stanchions can be spaced further apart (7').

Whenever possible stanchions should be placed in a symmetrical fashion in front of an artwork as this maintains good overall visual harmony.

INSTALLATION INSTRUCTIONS FOR GReY PPC

Please scroll down for stainless steel.

Stanchions are supplied in packs of two complete with an Allen key for assembly.

  1. Assemble the stanchion by placing the large cover over the heavy black baseplate.
  2. Remove the bolt from the end of the upright, fit the washer onto the bolt and place it through the central hole of the base plate and cover and into the end of the upright. Tighten securely with the Allen Key provided.
  3. Place the stanchions in position to protect the artwork allowing 5' to 7' between each. Be sure to check the cord does not ‘droop’ between stanchions.
  4. Remove the top caps using your finger or a small screwdriver and tie a simple ‘granny’ knot in the end of the elasticated cord. Pull it very tight and cut off any excess cord close to the knot.
  5. Push the knot into the recess in the top of the upright with the cord exiting through one of the slots and replace the cap.
  6. Pull the cord tight to the next stanchion with enough tension to make a straight line and push into the slots: straight across if it is a straight line or at right angles if it is at a corner.
  7. Repeat step 5 for the last stanchion or use a wall terminator.

In an installation where the object is completely surrounded, instead of two separate knots tie the two ends together with a reef knot, pull very tight and cut off the ends. If required cut off one of the cap legs to accommodate the size of this knot.

A line of stanchions can also end with the cord returning to the wall by using a wall terminator.

INSTALLATION INSTRUCTIONS FOR STAINLESS STEEL

Barriers are supplied in packs of two complete with an Allen key.

  1. Assemble the stanchion by placing the stainless steel cover over the heavy black baseplate.
  2. Remove the bolt from the end of the upright, fit the washer onto the bolt and place it through the central hole of the base plate and cover and into the end of the upright. Tighten securely with the Allen Key provided.
  3. Place the stanchions in position to protect the artwork allowing 5' to 7' between each. For the best result be sure to check that the cord does not ‘droop’ between stanchions.
  4. When you have the desired layout, unscrew the top cap until there is a gap large enough to insert the cord. Use a small Allen key or screwdriver in the hole on the side of the cap if additional grip is needed.
  5. Insert the end of the cord into the space under the cap and wrap the cord around the stem once or twice and out through one of the slots. Hold the cord in place and screw the cap down.
  6. For intermediate stanchions, pull the cord tight to the next stanchion with enough tension to make a straight line and feed the cord in through one slot, around the cap stem and out through the appropriate slot. Straight through for a line of stanchions and ninety degrees at a corner.
  7. Repeat step 5 for the last stanchion or use a wall terminator.
  8. When the layout is complete, gently tighten all caps to prevent ‘little fingers’ from removing them.
    Note: In an installation where the object is completely surrounded, repeat step 5 with both cord ends. In this instance it is only necessary to wrap once around the stem.


A line of stanchions can also end with the cord returning to the wall by using a wall terminator.